Product Description
Equipment Introduction:
Function:polish the surface of the bars/rods. Process introduction:
1, Remove the defects in the semi-finished bars to improve the surface quality of the rolling products, improve the percent of
pass of the rolling bars;
2, Polish the finished bars, improve the surface quality of the bars.
II. Equipment Parameters and Structure Description
* Equipment Description
Model 2M5020WB-6B Belt polishing machine is a kind of equipment for grinding the outer round surface of steel bar. The machine
tool mainly consists of six sets of sand belt (grinding wheel) grinding head assembly, conveying wheel mechanism, drive pressure
wheel assembly, automatic loading mechanism, automatic unloading mechanism, overall shield, circulation system, pneumatic system,
electrical control system, etc. The grinding process of the equipment: the bars are laid on the loading platform, then the loading
mechanism sends the bars to the conveying wheels, the wheels convey the bar to the grinding area driven by rotating press wheels ,
pass through 2 grinding wheel heads and 4 grinding belt heads. After the whole bar enters the conveying wheels in the unloading
area, bar is discharged through the unloading mechanism. When the diameter of bar is different, adjust the spacing between
conveying wheels to adapt to different diameters.
1, Remove the defects in the semi-finished bars to improve the surface quality of the rolling products, improve the percent of
pass of the rolling bars;
2, Polish the finished bars, improve the surface quality of the bars.
II. Equipment Parameters and Structure Description
* Equipment Description
Model 2M5020WB-6B Belt polishing machine is a kind of equipment for grinding the outer round surface of steel bar. The machine
tool mainly consists of six sets of sand belt (grinding wheel) grinding head assembly, conveying wheel mechanism, drive pressure
wheel assembly, automatic loading mechanism, automatic unloading mechanism, overall shield, circulation system, pneumatic system,
electrical control system, etc. The grinding process of the equipment: the bars are laid on the loading platform, then the loading
mechanism sends the bars to the conveying wheels, the wheels convey the bar to the grinding area driven by rotating press wheels ,
pass through 2 grinding wheel heads and 4 grinding belt heads. After the whole bar enters the conveying wheels in the unloading
area, bar is discharged through the unloading mechanism. When the diameter of bar is different, adjust the spacing between
conveying wheels to adapt to different diameters.
Specification
Main technical parameters:
1 Sand belt specification: 3480 × 150mm (perimeter × width)
2. Sand belt granularity: 60 # ~400 # (optional) * Grinding wheel specification: Φ 400 × 75mm (diameter × Width)
* Diameter range of to be processedbar: Φ 25~ 130mm
* Length range of the bar: 1700~3000mm
* bar Materials: Stainless steel, carbon steel Alloy steel
* bending degree of the bar: 3 / 1000mm
* Surface roughness of the barbefore grinding: cold-rolled surface
* Surface roughness after grinding: Ra ≤ 0.8 μ m
* Single bar weight: ≤ 400kg
* Grinding mode: Wet grinding
* Unilateral grinding depth: ≤ 0.2mm
* Specification of contact wheelof sand belt: Φ 400 × 150mm (Diameter × Width)
* Sand belt linearspeed: 30m/s
* Grinding wheelline speed: 45m/s
* Conveying wheel specification: φ 150 × 50mm
* Conveying wheel rotation speed: 20~80r/min
* Axial feed speed of the workpiece: 5~4.0m/min (Stepless speed adjustment, achieved by frequency conversion drive motor and
manual adjustment of conveying wheel angle)
* Grinding head motor power: 15kw (6 sets)
* Pressure-wheel drive motor power: 1 kw (9 sets)
* Power of conveying wheelssynchronous movement adjustment motor: 0.75 kw (2 sets)
20. Sewage pump motor power: 75KW
21. Power supply:AC, 3-phase,440v, 60Hz,
Input power: 105kw
22. Compressed air source:0.4MPa~0.6Mpa
0.3M ³/ hours
23.Overall dimension of machine: 15000 × 4000 × 3000mm (length *width* height)
24. Machine Weight: 20T
2.2.3 Structure Features
General structure, working principle and working characteristics (see attached drawing).
Main technical parameters:
1 Sand belt specification: 3480 × 150mm (perimeter × width)
2. Sand belt granularity: 60 # ~400 # (optional) * Grinding wheel specification: Φ 400 × 75mm (diameter × Width)
* Diameter range of to be processedbar: Φ 25~ 130mm
* Length range of the bar: 1700~3000mm
* bar Materials: Stainless steel, carbon steel Alloy steel
* bending degree of the bar: 3 / 1000mm
* Surface roughness of the barbefore grinding: cold-rolled surface
* Surface roughness after grinding: Ra ≤ 0.8 μ m
* Single bar weight: ≤ 400kg
* Grinding mode: Wet grinding
* Unilateral grinding depth: ≤ 0.2mm
* Specification of contact wheelof sand belt: Φ 400 × 150mm (Diameter × Width)
* Sand belt linearspeed: 30m/s
* Grinding wheelline speed: 45m/s
* Conveying wheel specification: φ 150 × 50mm
* Conveying wheel rotation speed: 20~80r/min
* Axial feed speed of the workpiece: 5~4.0m/min (Stepless speed adjustment, achieved by frequency conversion drive motor and
manual adjustment of conveying wheel angle)
* Grinding head motor power: 15kw (6 sets)
* Pressure-wheel drive motor power: 1 kw (9 sets)
* Power of conveying wheelssynchronous movement adjustment motor: 0.75 kw (2 sets)
20. Sewage pump motor power: 75KW
21. Power supply:AC, 3-phase,440v, 60Hz,
Input power: 105kw
22. Compressed air source:0.4MPa~0.6Mpa
0.3M ³/ hours
23.Overall dimension of machine: 15000 × 4000 × 3000mm (length *width* height)
24. Machine Weight: 20T
2.2.3 Structure Features
General structure, working principle and working characteristics (see attached drawing).
Product Display
Hot Tags: hg2m5020-6b six-head belt polishing machine, China hg2m5020-6b six-head belt polishing machine manufacturers, Bearing Steel Bar Peeling Machine, Auto Parts Peeler, Bright Bar Peeler, Metal Bar Peeler, Carbon Steel Bar Peeling Machine, Copper Bar Peeling
